ELEDing EE818WDC(WW) Use and Care Manual

Browse online or download Use and Care Manual for Infrared bulbs ELEDing EE818WDC(WW). eLEDing EE818WDC(WW) Use and Care Manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 4
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
1 – eLEDing Solar Light Body 1 – Rechargeable Li-Poly Battery 1 –
1 – Wall Mounting Plate w/hardware 2 – Hardware Package with Screws and Anchors
Initial Installation Set-up (Refer to Fig. 1)
Included in this package:
IMPORTANT …. Read this User Manual Before Installing...!!!
®
Connecting the Battery before setting up
1. The battery has been pre-charged before shipping and the light is ready for use
2. Make sure the main switch is in the OFF position
3. Open the battery cover on the back of the light and plug the battery into the connector and carefully make sure the plug position is
correct then replace the cover (Fig. 1-1)
4. Initially check the light and battery by moving the switch to AUTO then SMART (ON), it should light up, then turn the switch back to
OFF for installation
Mounting the Light Body
1. The light body must only be mounted in a vertical position and it should be mounted at least 6 to 10 feet above the ground
2. Choose a flat and safe mounting surface. Mark the screw positions through the mounting plate screw holes onto the mounting surface
Use 2 or 4 hole mount, (Fig. 1-2 & 1-3)
3. For wood, vinyl and metal surfaces mount the back plate directly with provided screws. Drill clearance holes using a 3/16" masonry bit
for surface of concrete, brick or stucco. Insert the anchors provided with screws then position the mounting plate and screw the
fasteners in securely
4. Attach the light body unit to the wall mounting plate:
Slide the whole light body onto the wall mount plate from top going down with the light body “hinged” to the mounting plate (Fig. 1-4)
Then secure the mounting with the small securing screw on bottom of the light body (Fig. 1-5)
5. With the light body firmly secured in it’s mounting position, the Pan & Tilt adjustment features can be used to adjust the direction of the
motion detector and the light head directions for optimal performance and coverage. The direction and angle of the motion detector can
be adjusted (Fig. 1-9). The LED light head can also be adjusted horizontally 180
o
, forward and backward 120
o
(Fig. 1-10)
Mounting and Connecting the Solar Panel
1. The solar panel must be mounted in a non-obstructed position where it will receive an average of at least 4 hours daily of direct sunlight
all year round. It should be mounted with a tilt of 35°- 80° degrees (Fig 1-6). A sturdy mounting location such as a wall, roof, on top of
patio, under the eaves, secure pole, or floor/ground base. This is required to make sure the solar panel is fasten down properly for all
weather conditions.
2. For Northern hemisphere installations the solar panel should be mounted with a Southerly facing position and visa-versa for Southern
hemisphere installation should face to the North (Australia, South Africa, South America e. g.)
3. Attach the hardware mounting bracket to the solar panel. Determine how far of the 10' connecting wire cord is needed to reach
the position of the light body and then tie the unused cord behind the solar panel with the plastic zip-tie that is provided (Fig. 1-7)
4. Then mark the screw holes through the mounting bracket and secure the solar panel in position with the provided hardware
5. Firmly plug the solar panel plug into the bottom of the light body (Fig. 1-8). The RED-LED indicator (in side the motion ball) will
begin to double flash (Fig. 1-8) indicating that charging status is active during a normal daytime sunny, partially sunny or cloudy day. If
this does not happen please check that the plug is fully plugged into the light body or if there is a problem with the wire.
Built with LED Smart Solar Light
Rev. EE818WDC 032015 Page 1
9
eLEDing SMART Lighting Profiles & Settings
eLEDing Intelligent microprocessor controlled Solar Light offers two
principal operating profile modes. The Sensitivity/Range of motion,
length of illuminating time, and levels of brightness and dimming are
set and controlled with adjustable dials (Fig. 2)
There are two principal operating profiles for the light. These are
AUTO profile and SMART-ON profile.
The family of eLEDing solar lights use an exclusive Intelligent Power
Management (IPM) embedded feature for managing and optimizing
the Lithium based battery for a full range of operation. This optimizes
the battery’s life cycle to adapt to most environmental conditions
allowing both the battery and light to perform for many years.
Fig. 2 Light Profiles & Settings
Battery will charge in any of the three switch position including OFF.
A Set-up/Walk test is used to establish the motion sensitivity, Delay Time
and Brightness level settings for the light. After the Set-up/Walk test is
completed the main switch can be set to either the AUTO lighting profile or
the SMART-ON (recommended) lighting profile (test is described on pg. 3)
Or
4.
5.
6.
3.
7.
8.
P
9.
Pan & Tilt
Pan & Tilt
p
10.
2 Screws
4 Screws
3.
1.
2.
Connect
the battery
before
using!
Page view 0
1 2 3 4

Summary of Contents

Page 1 - Rev. EE818WDC 032015 Page 1

1 – eLEDing Solar Light Body 1 – Rechargeable Li-Poly Battery 1 –1 – Wall Mounting Plate w/hardware 2 – Hardware Package w

Page 2

A) In Mode A maximum brightness is controlled and set by the user. In this mode the dual function Delay-Time dial functions as a Brightness dial for s

Page 3 - Optional Accessories:

Rev. EE818WDC 032015 Page 3Set Up-Walk Test Procedure and Adjustments1. To set up eLEDing for your applications the unit comes with a Set-up/Walk Tes

Page 4 - Specifications

Thank you for purchasing the eLEDing LED Smart Solar Lights. With its effortless setup and lightweight design the eLEDing LED Smart Light conforms to

Comments to this Manuals

No comments